Find best value and selection for your FISHER RS 717 AM FM Stereo Receiver with REMOTE search on eBay. World's leading marketplace. Find best value and selection for your FISHER STEREO RECEIVER RS 717 QUALITY VINTAGE AUDIO 80 watts search on eBay. World's leading marketplace. Fisher Rs 717 Manual Lawn. 5/21/2017 0 Comments. Request the Fisher RS-717 service manual. General information The Fisher RS-717 is a receiver in the. Fisher Rs 717 Manual Lawn. Pennsylvania State Employees' Retirement System. Pennsylvania SERS Reduces Investment Return and Inflation Assumptions, Continues Restructuring Public Markets Portfolio. The Board of the Pennsylvania State Employees' Retirement System today reduced the long- term.

Determining the Cause of the Problem Let's assume our system has a head unit, a crossover, a two channel amplifier and two door speakers with only the right speaker working (the left speaker is not working). If the door speakers are behind the door panels then we want to make sure the speaker is the problem before removing the panel. We'll work backwards starting with the amplifier and ending at the head unit. Testing for a Speaker Problem With the vehicle and the stereo turned off disconnect the speaker wires for both the left and right speakers at the amplifier. Now connect the left speaker to the right amplifier output (which we know works). Turn on the stereo system and make sure the balance is set to the middle position.If the speaker still doesn't work then the problem is somewhere between the amplifier and the speaker Testing for an Amplifier Problem Now we'll need to see if the amplifier channel is bad. Put the left speaker back on the left amplifier channel and the right speaker on the right amplifier channel.

This returns the speaker wiring to its original configuration. Again, with the vehicle and stereo off unplug the RCA cables from the amplifier's input and switch them so the left cable is in the right input and vice versa. Turn on the stereo system. Testing for an RCA Cable Problem For any intermediate components between the amplifier and the head unit follow these steps for each one. We only have a crossover so we'll just do this once. Begin by testing the RCA cables between the intermediate component and the amplifier.

Unplug both RCA cables from the intermediate component's output. Now plug the working channel's RCA cable into the non-working side of the crossover. In our case the working channel is the right so plug the right RCA cable from the amplifier into the left side of the crossover. A And N Pdf.

Turn on the stereo system. If the right channel continues to work then you know the problem is in the RCA cables between the amp and the crossover. Norinco Jw 14 Manual. Esting for a Crossover or Equalizer Problem At the input of the intermediate component (in our case the crossover) flip the RCA cables around (left to right input and vice versa).

Turn on the stereo system. If the right channel continues to work and the left channel continues to not work then you know the problem is in the intermediate component. Replace or repair this component. If the problem is now in the right speaker and the left speaker works then the problem lies before the crossover. Turn off the stereo system and return the RCA cables to their normal places.

Testing for a Head Unit or RCA Cable Problem Pull out the head unit from the dash so you can access the RCA cables. Unplug both RCA cables from the head unit. Do not disconnect any other wiring.

Plug the right RCA cable into the left channel of the head unit. Turn on the stereo system. Sep 29, 2016 .

You would have to install a speaker selection switch. You cannot directly hook up 2 amplifiers to one set of speakers without destroying one or both amplifiers.

Unfortunately, one set of amplifiers is inside your sound bar. An external switch would have to be installed on your sound bar as well as speaker terminals that would connect to your Fisher. If you have a line out or tape out on your Fisher, and you have an analog input on your sound bar, use could use that as an alternate solution. For more information, please visit my website at audioserviceclinic.com. Dec 01, 2013 . Depending on the model, there are two ways to connect a subwoofer to an amplifier, receiver or processor. The best way is to connect the subwoofer to the SUB OUT or LFE output of a receiver, but some subwoofers can be connected to the speaker level outputs of the receiver or amplifier.